"ELECTRO CHEMICAL ZINC PLATING FOLLOWED BY CHROMOTISING FOR SARATH/AK630 OF STAGE COMPONENT AS PER DRG.NO.- NCC/416
OTHER DETAILS FOR WORKS AND INSPECTION.
THE SCOPE OF WORK (ENCLOSED) SHOULD BE FOLLOWED. "
Specification
"ELECTRO CHEMICAL ZINC PLATING FOLLOWED BY CHROMOTISING FOR SARATH/AK630 OF STAGE COMPONENT AS PER DRG.NO.- NCC/416
OTHER DETAILS FOR WORKS AND INSPECTION.
THE SCOPE OF WORK (ENCLOSED) SHOULD BE FOLLOWED. "
Drawing no.
DRG.NO.- NCC/416
Manufacturing Technology
Testing / Inspection Facility
94
950000
Whole job
32002
ORDFYS/MSF/CPP/VENDOR REGISTRATION/18(1)/PV-1
Metal and Steel Factory
The General Manager,
Ishapore
Ishapore
Ishapur, West Bengal
743144
"M.S. STARTER PLATE SIZE - 20 MM X 1000 MM X 1200 MM AS PER MSF DRG NO - ESR/1000/03 . FULLY MACHINED AS PER DRAWING AND
FITTED WITH BOSS -03 NOS IN EACH PLATE . "
Specification
"M.S. STARTER PLATE SIZE - 20 MM X 1000 MM X 1200 MM AS PER MSF DRG NO - ESR/1000/03 . FULLY MACHINED AS PER DRAWING AND
FITTED WITH BOSS -03 NOS IN EACH PLATE . "
FERRO MOLYBDENUM TO SPECN IS:1469-1993,GR:Fe-Mo 63,C-10;CHEMCOMP.=Mo%:60-65,C%:0.10Mx,Si%:2.0Max,S%:0.08Max,P%:0.06MaxCu%:0.50Max,Al%:0.50Max,Pb%:0.01Max,Sn%:0.03Max.PARTICLE SIZE:Over 25 mm Upto and including 50 mm,Under size by mass:5%Max,Over size by mass:10%Max.OTHER REQUIREMENTS:AS PER SPECN
Specification
FERRO MOLYBDENUM TO SPECN IS:1469-1993,GR:Fe-Mo 63,C-10;CHEMCOMP.=Mo%:60-65,C%:0.10Mx,Si%:2.0Max,S%:0.08Max,P%:0.06MaxCu%:0.50Max,Al%:0.50Max,Pb%:0.01Max,Sn%:0.03Max.PARTICLE SIZE:Over 25 mm Upto and including 50 mm,Under size by mass:5%Max,Over size by mass:10%Max.OTHER REQUIREMENTS:AS PER SPECN
FERRO VANADIUM.TO SPECN.IS: 1466-1985,(Reaffirmed in 1996),GRADE-Fe V 55, (LC)(MATERIAL TO BE SUPPLIED IN SIZE BETWEEN 25MM TO 50MM).FIRM'S TEST CERTIFICATE FROM NABL ACCREDED LABY/GOVT.RECOGNISED LABY;AS PER SPECN.MUST BE ATTACHED WHILE SUPPLYING MATL
Specification
FERRO VANADIUM.TO SPECN.IS: 1466-1985,(Reaffirmed in 1996),GRADE-Fe V 55, (LC)(MATERIAL TO BE SUPPLIED IN SIZE BETWEEN 25MM TO 50MM).FIRM'S TEST CERTIFICATE FROM NABL ACCREDED LABY/GOVT.RECOGNISED LABY;AS PER SPECN.MUST BE ATTACHED WHILE SUPPLYING MATL
FERRO-CHROME ( HIGH CARBON ) TO SPECIFICATION IS: 1170-1992,GRADE- 1, DESIGNATION 7 Fe Cr-65, CHEM.COMP.:- Cr%:60-70,C%:6-8,Si%:1.5-4;RESIDUAL ELEMENTS & OTHERS: AS PER SPECN. PARTICLE SIZE: BETWEEN 100 MM TO 150 MM,UNDER SIZE: 5% MAX,OVERSIZE: 10% MAX. FREE FROM EXTRANEOUS CONTAMINATIONS ETC.
Specification
FERRO-CHROME ( HIGH CARBON ) TO SPECIFICATION IS: 1170-1992,GRADE- 1, DESIGNATION 7 Fe Cr-65, CHEM.COMP.:- Cr%:60-70,C%:6-8,Si%:1.5-4;RESIDUAL ELEMENTS & OTHERS: AS PER SPECN. PARTICLE SIZE: BETWEEN 100 MM TO 150 MM,UNDER SIZE: 5% MAX,OVERSIZE: 10% MAX. FREE FROM EXTRANEOUS CONTAMINATIONS ETC.
Drawing no.
Manufacturing Technology
Testing / Inspection Facility
04
75000
Kilogram
32004
ORDFYS/MSF/CPP/VENDOR REGISTRATION/18(1)/PV-1
Metal and Steel Factory
The General Manager,
Ishapore
Ishapore
Ishapur, West Bengal
743144
CANVAS COTTON 407 GM LOD IND/ADE/0087 Except That:-
1-Weight, gsm – 407+-5%.
2-Count of yarn :-Warp :-2 ply of 20s Single yarn
Warp :-3 ply of 24s Single yarn
(Note: The count of single yarn is approximate and given for the guidance of the manufacturers. The no. of plies, however, shall not be changed.)
3-No. of threads/ inch:-Warp:-92 Weft:-48
(The tolerance in no. of threads/inch shall be +- 5%)
COTTON FABRIC FOR S.D. PARACHUTE type II of IS:2970-1987 Reffirmed 2004 There shall be no presence of starch in appearance workmanship and finish and other respects not denined in the specification the material shall conform to the sealed pattern held in the custody of CQAT&C Kanpur. The bolt length/Roll length 40.00 Mtr. or above.
2.PACKING AND MARKING : As per relevant clause of specn.
AS PER TECH.PARTICULARS
(a) MASS/SQ MET : 58 GM (MAX)
(b) BREAKING STRENGTH, BOTH WAYS : 60 KGF (MIN)
(c) TEARING STRENGTH, BOTH WAYS : 1.7 KGF (MIN)
(d) AIR POROSITY : 7-10 CU.FT/SQ.FT/SEC.
(e) THICKNESS:0.11MM,MAX AT A PRESSUE OF 200GM/SQCM.
(f) WIDTH : 100 CM
(g) YARN LENIER DENSITY, BOTHWAYS : 45 DENIER(NORMAL)
(h) TWIST OF YARN :WARP:200 TPM, WEFT: 150TPM
(i) THREAD DENSITY, BOTHWAYS :48-50/CM.(j) WEAVE:2/1 TWILL
NOTE: THERE SHOULD NOT BE ANY TYPE OF YARN DISTORTION/SLIPPAG
SPECN-AS PER PARTICULARS.
(a) MASS/MET. :33 GM(MAX)
(b)BREAKING STRENGTH(BOTHWAYS) :38 KGF(MIN)TESTING METHOD OF
B.S.IS:1969-1968
(c)TEARING STRENGTH(BOTHWAYS) :1.7KGF(MIN)
TESTING METHOD OF TEARING STRENGTH IS:4726-1964 APP.'D'.
(d)AIRPOROSITY:16-22CV.FT/SQ.FT/SEC. (e)THICKNESS:0.07MM(MAX) AT PRESSURE 200GM/SQCM
(f)WIDTH: 100 CM.
(g)WEAVE :PLAIN
(h)YARN LINEAR DENSITY BOTHWAYS:30 DENIER(NOMINAL)
(i)TWIST OF YARN :WARP:200TPM, WEFT:SPIN(10-30 TPM)
(j)THREAD DENSITY BOTHWAYS :44-45 PER CM.
THERE SHOULD NOT BE ANY YARN DISTORTION/SLIPPAGE IN FABRIC
SPCN: ADRDE/SPECN/1980/5(a)In appearance, workmanship, feel, finish and others respects not defined in the specification the material shall conform to the sealed pattern held in the
custody of controller CQAT&C Kanpur and in addition the firm shall get, The name and/or trade mark woven/stamped along with selvedge at the interval of one meter on either side of the
fabric. (2)Packing & Marking:-as per relevant clause of specification. (3)Sampling plan:-As per relevant clause of specification
SPECIFICATION NO. : IS : 4726-1984 and to the following exceptions :- (i) The breaking strength shall be carried out by revelled strip method after conditioning the test specimen at 65 + 2% RH & 27 + 2 C for 24 Hrs. No individual reading for breaking strength test for warp and weft shall be
less than the value shown in ISI specn. NO.IS:4726-84.
(ii) 100 % Sampling/Testing/Inspection shall be resorted
(iii)Roll length shall be 80 M or above.(iv) A Flag allowance of 50 cm for each major defect flagged except for continuous defect which shall be given a one meter allowance for each meter in which defect occurs
Specn.-IS:2422-1985 Dye fastness to light may be obtained by Carbon arc method also in case Xenon arc is not available. (a)In appearance shade finish and all other respects not defined in this specification, the material shall conform to the corresponding sealed pattern held in the custody
of the Controller, CQAT&C, Kanpur.
(b) Sampling plan as per Annexure I attached
Spcn :-1. WEIGHT PER SQR.MTR.(IN GRMS)=115 gm.
2. WIDTH IN CM – 94
3. AIR POROSITY(Cub.Ft/Sqr.Ft./Sec.) - 25 TO 30.
4. BREAKING STRENGTH(In Kg)-50 Min. BOTH DIRECTION.
5. THICKNESS IN MM 0.25 (Max).
6. NUMBER OF THREAD/CM - 21/22 IN ONE DIRECTION. - 23/24 ON OTHER DIRECTION
7. TEX. OF YARN - 9.8 X 2 WARP - 9.4 X 2 WEFT
8. FINISHED GRAY MERCERISED
SPECN.NO. :AS PER FOLLOWING PARTICULARS.
a)Width 132 cms., (b)Thickness in mm at 200 gm/sq.cm 0.45,
(c)Weight/mt/Sq (in Gms) 107 Max.,(d) No. of mesh/Sq.inch- 140 ,(e) Tearing strength in kg.in both direction 3.2 min.(f)Bursting strength in kg. 11 kg. min, (g) B.S.in kg 5X20 cms strip length direction 40 min, width direction 24 min.
(h)Elongation at break length direction | 40% width direction 92.5 to 100%
AS PER PARTICULAR =WIDTH=94 CM
A.P.35+_5 Cuft/Sqft/Sec at 10"WHP
Weight/Sq.Metre=115-117 Gram
Thread /cm-Warp-28,WEft-25
Tex of Yarn
Tex x Fold-Warp-9.4x2,Weft-9.5x2
B.S.in Kg-Warp-53kg(min)
Weft-53kg(min.)
Weave-Plain
Finish-Grey Merecerised
